WARNING:Articles moved into the Archived collection were accurate at the "Last Update" date, but are not maintained from that date forward.
As such, Sun disclaims all implied or express warranties with respect to the information contained in such articles.
Document Audience:INTERNAL Archive
Document ID:I0344-1
Title:A few defective covers have been identified on the Ultra Enterprise 10000 system boards.
Copyright Notice:Copyright © 2005 Sun Microsystems, Inc. All Rights Reserved
Last Updated Date:1997-09-26

---------------------------------------------------------------------
        - Sun Proprietary/Confidential: Internal Use Only -
---------------------------------------------------------------------  
                        FIELD INFORMATION NOTICE
                  (For Authorized Distribution by SunService)
FIN #: I0344-1
Synopsis: A few defective covers have been identified on the Ultra Enterprise 10000 system boards.
Create Date: Sep/25/97
Keywords: 

A few defective covers have been identified on the Ultra Enterprise 10000 system boards.

Product Category: System
Product Affected: 
Ultra Enterprise 10000
Parts Affected: 
501-4347-09		E10000 System Board 
 	F501-4347-09		FRU, E10000 System Board 
 
 	407-6575-012 Rev 04	Cover, System Board
References: 
Issue Description: 
It has been discovered that the cover for the E10000 system board is
 missing a clearance hole for a centerplane guidepin.  This is ONLY
 needed for slot 07 on the UE10000, all other slots do not require this
 clearance hole.
 
 Attempting to install a system board with a defective cover will cause
 mechanical interference between the system board and the centerplane
 guidepin, resulting in the system board being unable to be installed in
 slot 07 of the UE10000 chassis.  For any other slot there is no
 interference.
 
 The defective covers have been traced to one defective lot from the
 sheet metal supplier.  Inspections are now in place at the supplier to
 prevent from happening again but, there remains 47 covers unaccounted
 for, which are assumed to be in the field.  BSD Quality Engineering
 will monitor all cover returns in an attempt to account for the
 outstanding 47 covers.
Corrective Action: 
Prior to installing any system board into slot 07, verify that there is
 a clearance hole (approx. 3/8" or 8mm) located in the lower rear of the
 system board module, below where the connector will engage the
 centerplane.  It is the only hole located on the rear of the system
 board module.
 
 The problem only exists for installation of a system board in slot 07,
 all other slots (00-06, 08-15) are NOT affected.
 
 If reconfiguring an UE10000 and a system board is to be moved from some
 other slot to slot 07, verify the hole is present prior to installing.
Comments: 
For existing systems, if configurations are not changed, or if
 a system board is inspected prior to installation in slot 07,
 there will be no adverse effect.
 
 If a failed system board in slot 07 is to be replaced by an FRU, and
 the FRU happens to have a defective cover, the cover of the failed
 system board can be exchanged with the defective cover on the FRU and
 the replacement completed.  Return the defective cover with the failed
 system board and it will be upgraded at the BSD repair depot.  Be sure
 to follow proper ESD procedures when exchanging the covers.
 
 SunService Logistics has introduced an additional new part number,
 F501-4786-01 which does not have the defective covers associated with
 it.
 
 --------------------------------------------------------------------------
 SunWeb Access: 
 ______________
 
 All released FINs and FCOs can be accessed internally on the SunWeb using
 your favorite network browser as follows:
 
 * Access the top level URL of http://cte.corp/FIN_FCO/
 
 * From there, select the appropriate link to query or browse the FIN and
   FCO Homepage collections.
 
 Supporting documents for FIN/FCOs can be found on Edist.  Edist can be 
 accessed internally at the following URL: http://edist.corp/.
  
 * From there, follow the hyperlink path of "SunService Documentation" and 
   click on "FIN & FCO attachments", then choose the appropriate folder, FIN
   or FCO.  This will display supporting directories/files for FINs or FCOs.
 
 --------------------------------------------------------------------------
 General:
 ________
 
 Send questions or comments to finfco-manager@cte.Corp
Statusinactive