20GB 4 mm DDS-1 Autoloader
| Servers: |
SPARCcenter 2000 |
Options 825 / 826 / 827
| 370-1616 |
370-1617 |
Archive 4584NP
Light Grey Bezel |
Archive 4584NP
Black Bezel |
| Operator Panel |
 |
|
| LMJB0153 PCB |
 |
Address Select Switch Cable
 |
In the Multi-Tape Backup Tray and SC2000, orient the Address Select
Switch Cable as shown, and plug it into JP6. |
Note
- Remove the mylar sheet from the bottom of the drive before installation.
References
20GB 4mm Autoloader Destop Storage Module Installation and User's Guide, 801-5401.
-
Product Note, 801-6234.
Jumper and Switch Settings
JP4
| PINS |
SETTING |
DESCRIPTION |
| 1-2 |
Out |
Disable TERMPWR to bus |
| 1-2 |
In |
Enable TERMPWR to bus |
|
|
JP6
| SCSI ID |
3 |
2 |
1 |
| 0 |
Out |
Out |
Out |
| 1 |
Out |
Out |
In |
| 2 |
Out |
In |
Out |
| 3 |
Out |
In |
In |
| 4 |
In |
Out |
Out |
| 5 |
In |
Out |
In |
| 6 |
In |
In |
Out |
|
|
SW1
| SWITCH |
SETTING |
DESCRIPTION |
| 1 |
Off |
Enable SCSI ID 0 = 20
|
| 2 |
Off |
Enable SCSI ID 1 = 21 |
| 3 |
Off |
Enable SCSI ID 2 = 22 |
| 4 |
On |
Enable SCSI-2 mode |
| 5 |
On |
Enable parity |
| 6 |
Off |
Enable data compression |
| 7 |
Off |
Reserved for factory use |
| 8 |
On |
Enable power-on self test |
|
Switch Settings
| LMJB0178 PCB |
 |
|
| S1 |
| SWITCH |
SETTING |
DESCRIPTION |
1
2 |
Off*
Off* |
English language display |
1
2 |
Off
On |
French language display |
1
2 |
On
On |
Spanish language display |
1
2 |
On
Off |
German language display |
3
3 |
Off
On* |
Stop after last tape
Restart at Tape 1 after last tape |
4
4 |
On*
Off |
High intensity display
Low intensity display |
| 5 |
On* |
Enable power-on self test |
| 6 |
Off |
Not used |
| 7 |
Off |
Not used |
* Default settings
|
|
|
| Auto-Loader |
 |
|
| S5 |
| SWITCH |
SETTING |
DESCRIPTION |
| 1 |
Off*
On |
Horizontal character display
Vertical character display |
| 2 |
Off
On* |
Do NOT load tape on power-up
Load tape on power-up |
| 3 |
Off
On* |
Stop after last tape
Restart at first tape after last tape |
| 4 |
Off |
Not used |
* Default settings
|
|
Notes
- The minimum operating system is Solaris 2.2.
- Solaris 2.2 reads and writes in low-density or high-density mode.
- The 4-Tape Magazine part number is 370-1683-01.
- The Blank 90 Meter Tape part number is 370-1612-01
- The Cleaning Kit part number is 370-1613-01.
- Firmware update tape 4.CDA-424 is part number 370-2867-01.
- Firmware update tape 4.CDB-424 is part number 370-3270-01.
References
-
20 Gbyte 4mm Tape Auto-Loader Installation Manual, 801-4976.
-
20 Gbyte 4mm Tape Auto-Loader User's Guide, 801-4977.
|
