---

Sun Blade X8450

X8450-44L1860-82	X8450-44M2130-82	X8450-44M2400-B2
594-5308 16GB Memory 4× 1.86GHz Xeon L7345	594-5309 16GB Memory 4× 2.13GHz Xeon E7320	594-5310 32GB Memory 4× 2.40GHz Xeon E7340

X8450-AA	501-7883	541-2538	F541-2538
599-3491 0MB Memory w/o Processor w/o Disk Drive	0MB Blade w/o Sheetmetal w/o Processors w/o Heatsinks	0MB Assembly w/o Processors w/o Heatsinks with Service Processor	0MB FRU w/o Processors with Heatsinks with Service Processor

Headers and Jumpers

LOCATION	PINS	SETTING	DESCRIPTION
J4	1-2 3-4 5-6 7-8	Out Out In In	Boot Select (default = reboot) Flash Boat (default) BIOS Top Block Lock (default) BIOS Write Protect (default)
J14	1-2 3-4 5-6 7-8	In Out Out Out	Unknown (default) Unknown (default) (see notes) Unknown (default) (see notes) Clear BIOS Password (default)
J12	3	Out	VRM JMPR (default)
J15	3	Out	CPLD Test Mode (default)
J19	6	n/a	Bench Test Fan Header
J22	3	n/a	Bench Test 48V Enable Header
J26	10	n/a	CPLD Download Header
J31	16	n/a	JTAG Header
J65	16	n/a	JTAG Header

Sun Blade 8000 Modular System Codename: Andromeda Sun Blade X8450 Codename: Scorpio

Notes

1. The minimum Solaris operating system is Solaris 10 8/07.
2. Two-processor configurations require two 541-2921 Baffles.
   X8450-AA-AIRBAF includes two 541-2921 Baffles.

Blade Notes

1. Use a 9/64-inch Allen wrench to remove the heatsink shoulder screws.
2. The FRU includes four pre-greased heatsinks 310-0146.
3. The FRU includes four alcohol wipes and four 310-0065 thermal grease syringes.
4. The Module FRU does not include heatsink mounting hardware.
5. Use shoulder screw 240-4717, spring 240-6109, and washer 240-4841.
6. Use coin cell battery FRU 150-3993.

Heatsink Notes

1. Heatsink 310-0146 is pre-greased with ShinEtsu G751 or X23-7783D.
2. FRU F310-0146 includes one alcohol wipe and one 310-0065 thermal grease syringe.
3. Each 310-0065 syringe includes 0.5 Grams (~= 0.3ml) of ShinEtsu X23-7783D.
4. Each Xeon processor requires approximately 0.2ml of thermal grease.
5. Use a pre-greased heatsink or a thermal grease syringe, but not both.

Jumper J4 Notes

1. Pins 3-4 and 5-6 are installed to write enable the BIOS.
2. Pins 3-4 and 5-6 are removed to write protect the BIOS.
3. Jumper functionality and usage is not documented in the product manuals.

Jumper J14 Notes

1. Pins 1 and 2 are not connected in schematic 502-7883-03.
2. Pins 1 and 2 are silkscreened TPM PP on system board 501-7883.
3. Pins 3 and 4 are described as HOST MFG MODE in schematic 502-7883-03.
4. Pins 3 and 4 are silkscreened BIOS REC on system board 501-7883.
5. Pins 5 and 6 are described as FORCE BIOS RECOVERY in schematic 502-7883-03.
6. Pins 5 and 6 are silkscreened MFG MODE on system board 501-7883.

References

1. Sun Blade 8000 Modular System Installation Guide, 819-5647.
2. Sun Blade 8000 Modular System Product Notes, 819-5651.